Product Index

Preview Image Name Short description
Application Conformal Coating
Board InverterThe Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.
DL ConveyorThe Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.
DL Turn UnitThe Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.
FIFO Buffer 10The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.
Animation
Flash Off Conveyor
High Top
Flash Off and Inspection Conveyor with Glass Door
Suitable for conformal coating applications with pallets or boards. The sliding glass door gives access to the internal conveyor and boards. Optional- High power UV blue inspection light or switch selectable white light. Ventilation guard with infeed blocking. Timer for controlled flash off time
Up and Down LiftUp and Down Lift
for pallets and solder frames, to be placed in the beginning or end of a production line. Standard or special infeed and outfeed heights.
UV 1600 UV Conformal Coating Curing Oven

Flexible
Multi-wave-length Arc-lamps cures coatings and glues without the need for change of type of lamps for different material.

Compact
Overall length of only 1600 mm, including -Inspection module -Dual Arc lamp ramps and cooling zone.

Energy efficient
Energy consumption is controlled by the built-in PLC. UV lamps go to stand by mode when no PC boards are in the machine.Only lamps needed for actual board width is turned on for lowest energy consumption

UV Inspection StationThe UV Inspection Station is suitable for solvent or UV cured coating or glue. For inspection of wet material connect exhaust system. The rigid framework makes it possible to add-on option for transporting heavy load carriers up to 15 kg. Communication with preceding and following units is done via the standard SMEMA interface
Application
SMT Line
Automatic LoaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.
Automatic ReloaderThe Reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.
Automatic UnloaderThe Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
Board InverterThe Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.
Board TransferThe board transfer system is a sophisticated solution for dividing, merging, or rerouting production lines by transferring boards between them. The machine consists of a traverse unit and a board carrying shuttle conveyor.
Buffer Unit
FIFO LIFO
The Buffer unit is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems.
DestackerThe Destacker separates a batch of PCBs and transports them one by one to the following machine.
DL ConveyorThe Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.
DL Turn UnitThe Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.
Dual UnloaderThe Dual Unloader consists of a conveyor mounted on an Y/Z table that receives and distributes PCBs from an upstream machine into one or two magazines, depending on selected work mode. If the pass/fail function is activated, good and bad PCBs will be separated and stored in different magazines.
FIFO Buffer 10The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.
Animation
In-line Magazine BufferThe Magazine buffer is placed in the line to balance board flow in FIFO or LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or line merger in Pass through mode. The magazine can be removed/exchanged at any time in all work modes.
Large Board Conveyor T5 and T6

The large board conveyor is based on the standard transport/buffer conveyor with the following main differences: reinforced rail structure, rail suspension, and belt driving mechanism. Each section of the conveyor has its own powerful DC motor that drives the belt on both sides, and provides smooth, reliable transportation of PCBs through an electronics assembly line.

Light ConveyorThe Light Conveyor is a cost effective product, aimed at customers that are interested in endless reliability, very low maintenance and safe transportation of PCBs through an electronics assembly line, without the advanced functions and optional accessories offered by our high-end conveyors.
Light Loader and UnloaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
Manual Gate ConveyorThe manual gate conveyor allows people and vehicles to go through, rather than round a complete line. It consists of two conveyor sections, one fixed and one jointed.
Mini BufferThe Mini buffer consists of a vertical buffer and a 500mm conveyor, and is placed in the line to balance board flow in LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or good/bad board separator in Triggered mode. Width adjustment, work mode, and other functions, are all accessed from the hand control unit, which makes the unit easily managed.
PCB inspection liftThe PCB reject & inspection lift is an option for 1000mm and 1500mm conveyors, and enables Good or No Good PCB separation and inspection. The lift has three different work modes. Reject mode, inspection mode, and pass through.
Single LoaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.
Single ReloaderThe Single reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.
Single UnloaderThe Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
T3 ConveyorThe T3 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.Length from 500 mm to 2500 mm.
Standard Conveyor
Packing Conveyor
Unpacking Conveyor
T3 WorkstationThe T3 workstation is built around the standard T3 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.
T4 ConveyorThe T4 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.
Standard Conveyor
Packing Conveyor
Unpacking Conveyor
T4 WorkstationThe T4 workstation is built around the standard T4 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.
Telescopic Gate ConveyorThe Telescopic gate conveyor is a fully automated pass through conveyor that allows people and vehicles to go through, rather than round a complete line. Since the retracted position of the telescopic conveyor is its idle position there is no need to press any buttons to pass through the line.
Turn UnitThe Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.
Turn Unit
Application
Wave Soldering
Up and Down LiftUp and Down Lift
for pallets and solder frames, to be placed in the beginning or end of a production line. Standard or special infeed and outfeed heights.
Featured
DL ConveyorThe Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.
FIFO Buffer 10The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.
Animation
Buffer
Buffer Unit
FIFO LIFO
The Buffer unit is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems.
FIFO Buffer 10The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.
Animation
In-line Magazine BufferThe Magazine buffer is placed in the line to balance board flow in FIFO or LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or line merger in Pass through mode. The magazine can be removed/exchanged at any time in all work modes.
Mini BufferThe Mini buffer consists of a vertical buffer and a 500mm conveyor, and is placed in the line to balance board flow in LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or good/bad board separator in Triggered mode. Width adjustment, work mode, and other functions, are all accessed from the hand control unit, which makes the unit easily managed.
Conveyors
Flash Off Conveyor
High Top
Flash Off and Inspection Conveyor with Glass Door
Suitable for conformal coating applications with pallets or boards. The sliding glass door gives access to the internal conveyor and boards. Optional- High power UV blue inspection light or switch selectable white light. Ventilation guard with infeed blocking. Timer for controlled flash off time
Large Board Conveyor T5 and T6

The large board conveyor is based on the standard transport/buffer conveyor with the following main differences: reinforced rail structure, rail suspension, and belt driving mechanism. Each section of the conveyor has its own powerful DC motor that drives the belt on both sides, and provides smooth, reliable transportation of PCBs through an electronics assembly line.

Light ConveyorThe Light Conveyor is a cost effective product, aimed at customers that are interested in endless reliability, very low maintenance and safe transportation of PCBs through an electronics assembly line, without the advanced functions and optional accessories offered by our high-end conveyors.
T3 ConveyorThe T3 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.Length from 500 mm to 2500 mm.
Standard Conveyor
Packing Conveyor
Unpacking Conveyor
T3 WorkstationThe T3 workstation is built around the standard T3 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.
T4 ConveyorThe T4 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.
Standard Conveyor
Packing Conveyor
Unpacking Conveyor
T4 WorkstationThe T4 workstation is built around the standard T4 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.
UV Inspection StationThe UV Inspection Station is suitable for solvent or UV cured coating or glue. For inspection of wet material connect exhaust system. The rigid framework makes it possible to add-on option for transporting heavy load carriers up to 15 kg. Communication with preceding and following units is done via the standard SMEMA interface
Dual Lane
DL ConveyorThe Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.
DL Turn UnitThe Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.
Gates
Manual Gate ConveyorThe manual gate conveyor allows people and vehicles to go through, rather than round a complete line. It consists of two conveyor sections, one fixed and one jointed.
Telescopic Gate ConveyorThe Telescopic gate conveyor is a fully automated pass through conveyor that allows people and vehicles to go through, rather than round a complete line. Since the retracted position of the telescopic conveyor is its idle position there is no need to press any buttons to pass through the line.
Loaders/Unloaders
Automatic LoaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.
Automatic ReloaderThe Reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.
Automatic UnloaderThe Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
Dual UnloaderThe Dual Unloader consists of a conveyor mounted on an Y/Z table that receives and distributes PCBs from an upstream machine into one or two magazines, depending on selected work mode. If the pass/fail function is activated, good and bad PCBs will be separated and stored in different magazines.
Light Loader and UnloaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
Single LoaderThe Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.
Single ReloaderThe Single reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.
Single UnloaderThe Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.
Other
Board InverterThe Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.
Board TransferThe board transfer system is a sophisticated solution for dividing, merging, or rerouting production lines by transferring boards between them. The machine consists of a traverse unit and a board carrying shuttle conveyor.
DestackerThe Destacker separates a batch of PCBs and transports them one by one to the following machine.
PCB inspection liftThe PCB reject & inspection lift is an option for 1000mm and 1500mm conveyors, and enables Good or No Good PCB separation and inspection. The lift has three different work modes. Reject mode, inspection mode, and pass through.
Turn UnitThe Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.
Turn Unit
Up and Down LiftUp and Down Lift
for pallets and solder frames, to be placed in the beginning or end of a production line. Standard or special infeed and outfeed heights.

News

Heating Conveyors
Contact Us for more information